Output Ratings:

Output Current

0-1.7 A

Output Ratings at the front panel binding posts:

Output Power

1020 W

Voltage

20 mV

Load Regulation:

Current

2.5 mA

Voltage (0.5% of Vmax + 1 count)

7 V

Output Noise & Ripple:

Voltage (p-p) (0-20 MHz)

300 mV

Voltage (0.05% of Vmax)

300 mV

Temperature coefficient:

Current (0.03% of Imax/° C)

0.48 mA

Line Drop Compensation

5 V/line

Efficiency:

85%

Program Resolution (16-bit):

Current

0.03 mA

Program Accuracy:

Current (0.3% + 10 mA)

80 mA (+/- 0.1%)

Readback Resolution (16-bit):

Current

0.03 mA

Voltage (0.2% + 20 mV)

300 mV (+/- 0.35%)

1. Specifications indicate typical performance at 25 ° C +/- 5° C, nominal line input of 120 VAC.

2. For input voltage variation over the AC input voltage range, with constant rated load.

3. For 0-100% load variation, with constant nominal line voltage. Measured at the rear panel output connector unless stated otherwise.

4. Maximum drift over 8 hours with constant line, load and temperature, after 30 minute warm-up.

5. Change in output per ° C change in ambient temperature, with constant line and load.

6. Line drop is subtracted from total voltage available at supply output.

7. Typical efficiency at 115 VAC input and rated output power.

8. Apply accuracy specifications according to the following voltage program accuracy example:
    Set a model 20-130 power supply to 10 volts. The expected result will be within the range of 10 volts +/- 75 mV +/-
    0.12% of the set voltage of 10 volts.

Operational AC input voltage

85-250 VAC, 47-63 Hz; power factor corrected. Derate maximum output power for 900 W for AC input less than 95 V.

Power Factor

0.99 minimum for full load and 120 VAC input

Switching Frequency

7.5 V to 300 V models: nominal 125 kHz (250 kHz output ripple); 600 V model: nominal 62.5 kHz (125 kHz output ripple)

Voltage Mode Transient Response Time

1 ms for output voltage to recover within 0.5 % of its previous level after a step change in load current of up to 50% of rated output

Remote On/Off and Interlock

2.5-15 V signal or TTL-compatible input, selectable logic

Remote Analog Monitoring

Voltage and current monitor outputs 0-5 V (default), 0-10 V ranges for 0-100% of output

Operating Temperature Range

32° F to 104 ° F (0° C to 40° C)

Humidity Range

Up to 80% RH, non-condensing

Front Panel Voltage Control Resolution

0.02% of maximum voltage

Main Output Connector

7.5 to 40 V models: nickel-plated copper bus bars; 60 V to 600 V models: 4-terminal wire clamp connector for DC output and local sense

Dimensions (H x W x D)

3.4 x 8.5 x 18.6” (86.4 x 216.0 x 472.2 mm)

GPIB-XHR

GPIB Interface card (16-bit)

ISOL-XHR

ISOL Interface card provides isolated analog control and readback

M22a

No front binding posts

RM-XHR

19-inch rack mount kit for up to two XHR power supplies

CE-marked units meet: EN61010-1, EN61000-6-2 and EN61000-6-4; CSA C/US certified to UL61010-1B and CSA C22.2 No 1010.1; Meets USA EMC standard: FCC, part 15B, class A; Meets Canadian EMC standard: ICES-001, Class A.

Note: Specifications subject to change without notice.