Sorensen XDL56-4 DC Power Supply 112 W, 0-56 V, 0-4 A, 3 ranges.

Home > SHOP ALL PRODUCTS > Power Supplies > DC power supplies >

List Price: $1,510.84 US Dollars

Availability: Ask for availability +1 (619) 879-6696
Product Code: XDL 56-4

Description

Application Notes

Datasheet PDF Format

	Electrical Specifications
	Output ranges:
	Range 1	0-56 V, 0-2 A
	Range 2	0-25 V, 0-4 A
	Range 3	0-56 V, 0-500.0 mA
	Outputs	1
	Output power	112 W
	Interface (GPIB/RS-232/USB)	No
	Voltage setting	By floating point numeric entry or rotary jog wheel; resolution 1 mV
	Current setting	By floating point numeric entry or rotary jog wheel; resolution 1 mV or 0.1 mA depending on range
	Setting accuracy	Voltage - 0.03% +/- 5 mV. Current 0.2% +/- 5 mA, 0.5 mA
	Output mode	Operation in constant voltage or constant current modes with automatice cross-over and mode indication by LEDs
	DC output switch	Sets output voltage and current levels to zero when Off
	Output terminals	4mm terminals on 19mm (0.75") spacing
	Load regulation	Voltage: <0.01% + 2mV Current: <0.01% + 250mA; <0.01% + 50mA on 500mA range (measured at output terminals using remote sense)
	Line regulation	Voltage: <0.01% + 2 mV for 10% line change Current: <0.01% + 250mA; <0.01% + 50mA on 500mA range
	Ripple and Noise	Typically <0.35mV rms 2m V p-p CV mode, and <0.2mA rms, <20mA rms (500 mA range) CI mode
	Transient response	50ms to within 15 mV of set level for a change in load current from full load to half load or vice versa
	Temperature coefficient	< +/- (50ppm + 0.5 mV)/oC (voltage)
	Remote sense	Eliminates up to 0.5 V drop per lead. Remote sense operation selected from front panel and indicated by LED
	Sense terminals	Recessed sprung sockets for direct insertion of wires. Duplicated on rear terminal block (P versions only)
	General Specifications
	Power requirements	115 V or 230 V +/- 10% (adjustable internally, option HV for factory set 230 VAC input), 50/60 Hz. Installation Category ll
	Operating range	5oC to 40oC, 20% to 80% RH
	Storage range	-40oC to 70oC
	Dimensions (HxWxD)	6.3 x 5.5 x 11.4"/160 x 140 x 290 mm
	Weight	11.9 lbs/5.4 kg
	Benchtop Operation	Folding legs are incorporated that can be used to angle the front panel upwards when required
	Rack mount operation	19 inch 4U mount for up to three single output units or one triple plus one single; Blanking plates available for un-used sections.
	Warranty	3 years
	Output Protection and Metering
	Output protection	Output will withstand forward voltages of up to 20 V above rated output voltage. Reverse protection by diode clamp for current up to 3 A
	Fault condition trip	The output will be shut down if any of the four trip conditions listed below occur. In addition to the output eing set Off, an isolated rear panel signal is also activated.
	Over voltage (OVP)	Settable 1V to 62 V in 0.1 V steps
	Over current (OCP)	Settable 0.1 A to 4.4 A in 0.01 A steps
	Over temperature	Monitors internal temperature rise to protect against excess ambient temperature or blocked ventilation slots
	Sense Error	Monitors the voltage between the remote sense terminals and output terminals to protect against mis-wiring
	Trip output signal	Isolated open-collector output signal on rear panel
	Meter resolution and accuracy:
	Voltage (CI mode):	Resolution 10 mV Accuracy +/- (0.1% of reading + 10 mV)
	Current (CV mode):	Resolution 0.001 A; 0.1 A on 500 mA range Accuracy +/- (0.2% + 0.005 A); +/- (0.2% + 0.5 mA) on 500 mA range
	V x A	Resolution 0.01 W; 0.001 W on 500 mA range Accuracy +/- (0.3% + 0.05 W); +/- (0.3% +0 0.005 W) on 500 mA range
	Store/Recall Settings
	Number of stores	10 plus power-down store
	Memory type	Non-volatile using EEPROM
	Parameters stored	Range, Set volts, Set current, OVP, OCP
	Recall system	Settings are previewed onto the displays before being actioned
	Bus Interfaces (P Suffix versions)
	USB	Standard USB hardware connection Supplied with device driver for Win 98 or above. Operates as a virtual COM port.
	RS-232	Variable baud rate 19,200 max. Single instrument or Addressable RS-232
	GPIB	Conforming with IEEE-488.1 and IEEE-488.2 (N.B. All three interfaces incorporate full control, readback and status reporting)
	BUS type selection	From front panel (GPIB/RS-232/USB)
	Address selection	From front panel (1 to 31)
	Baud selection	RS-232 only. Fron front panel (600 to 19200 baud)
	Setting resolution	Voltage - 1mV, Current 0.1 mA (0.1 mA on 500 mA range)
	Accuracy	See specifications under Outputs and Metering
	Remote control response time:
	Interface	Typically < 80 ms
	Output voltage	Response time varies with range and load conditions. Typical time to settle to within 1% of the total excursion on a 35 V / 3 A range with full load is <25 ms. With no load it is <7 ms for an upward charge and < 600 ms for downward.
	Regulatory Approvals
	CE-marked units meet: EN61010-1 and EN61326

1. General specifications apply for 5 to 4oC temperature range. Accuracy specifications apply for 18 to 28oC temperature range after 1 hour warm-up with no load and
calibration at 23oC. Typical specifications are determined by design and not guaranteed.

Note: Specifications are subject to change without notice.
To compare models, please download the Product Data Sheet.

Features

Key Features

Multiple voltage⁄current ranges
Direct numeric entry and incremental rotary control of voltage and current
Remote or local sense
Illuminated keys and display legends
Up to ten store/recall set-ups (30 set–ups for triple output)
Power output display
Link and copy mode Protection
Over voltage protection
Over current protection
Over temperature protection
Sense protection

The Sorensen XDL series represents the "next generation" of high performance laboratory power supplies. The XDL provides multiple ranges for increased current capability at lower voltages and uses pure linear technology. Unlike other digitally controlled units, the XDL series provides both numeric and rotary control while the illuminated keys and display legends provide instant confirmation of settings and status.

For added convenience the Sorensen XDL series provides storage of up to 10 power supply set-ups in non-volatile memory (30 set-ups for a triple). There are also fully adjustable over-voltage and over-current trips.The XDL series also provides full remote sense capability via dedicated sense terminals.

The XDL triple output model features link and copy mode for convenience. When linked, keyboard and jog wheel control operates both outputs simultaneously. The copy function copies all settings for output 1 to output 2.

Share your knowledge of this product with other customers... Be the first to write a review

Browse for more products in the same category as this item:

SHOP ALL PRODUCTS > Power Supplies > DC power supplies
SHOP ALL PRODUCTS > Power Supplies > DC power supplies > Less than 600 W power supplies
SHOP ALL PRODUCTS > Brands > Sorensen
SHOP ALL PRODUCTS > Power Supplies
SHOP ALL PRODUCTS > Brands
SHOP ALL PRODUCTS

	Instek GPE-4323 212W 4 Channel DC Power Supply $369.90
	BK Precision 9115-AT Auto Range DC Power Supply 80V/60A/1200W $3,160.00
	Amrel PLW9K-1000-40 DC Electronic Load, 9KW, 1000 Volts, 40 Amps $40,454.70 US Dollars
	Preen AC POWER AFC-33800 AC Power Supply 300 Volts, 1111.1 Amps. 800 KvA Three Phase Call us for Price and Availability. (619) 879-6696
	Sorensen XT120-0.5 DC Power Supply 60 W, 0-120 V, 0- 0.5 A. Discontinued
	Rigol DS1104Z-S 100 MHz Digital Oscilloscope with 4 channels and 25 MHz 2 channel integrated source plus 12 Mpt memory and connectivity and 1 GSa/sec sampling. Discontinued Product
	Instek APS-001 GPIB Interface card for APS-7050/APS-7100 $236.00
	Sorensen SGA 1000-5, Programmable Power Supply 5kW 1000V 5A Call us for Price and Availability. (619) 879-6696
	Sorensen SGA 250-100, Programmable Power Supply 25kW 250V 100A $30,107.70 US Dollars